CWS Sliding & Patio Doors Nationwide | TruePane Windows & Doors

CWS Sliding & Patio Doors: The Palmetto Bay Owner’s Guide

If you’re searching for CWS sliding or patio door parts in Palmetto Bay, here’s the short answer: we stock CWS-compatible rollers, handles, locks, tracks, weatherstripping, and glass packages, and most replacement work runs $180 to $650 installed depending on what actually failed. We carry OEM-spec parts and quality aftermarket equivalents on the truck, which means we can usually complete the swap in one visit. Most Palmetto Bay homeowners discover a failing CWS door the way you probably did: the door started dragging in July, or the handle quit latching after a thunderstorm, or you noticed daylight sneaking under the panel where it used to seal tight. Salt air and humidity off Biscayne Bay work on these doors year round, and the parts that fail first are almost always the ones that move.

Call (386) 200-9224

Which CWS Models This Applies To

CWS built sliding glass doors and patio doors across several series over the years, and parts are not all interchangeable. The best way to identify what you have is to look at the door panel’s edge or the head track for a small etched or stickered label. Older CWS doors commonly show the series code near the lock stile. If the label is gone, we measure the roller housing width and the panel thickness because those two dimensions tell us more than any model number. In Palmetto Bay we see a lot of CWS doors from the 1990s and early 2000s where the original roller assemblies were nylon-wheeled and not sealed. Once that nylon wears flat, the panel rides on the aluminum housing and starts grinding the track. For most CWS doors we recommend the aftermarket stainless-steel roller assembly over the OEM nylon one. The housing dimensions match; the wheel just lasts longer in salt air. Dale Kessler has pulled enough of these apart to know that if the track is scored, new rollers alone will not fix the drag, and that’s the kind of thing we check before we quote.

Signs Your CWS Sliding & Patio Doors Is Failing

• The door drags or takes real effort to open. This is almost always a roller failure. Nylon wheels flatten, the panel drops, and the door grinds on the track. Left too long, the track gets scored and the repair cost climbs.
• The handle turns but the latch will not catch. The mortise lock inside the stile has a spring and pawl that corrode in Palmetto Bay humidity. A door that will not latch is more than inconvenient; it leaves the panel loose in the opening.
• You can feel air or see light at the meeting stile or bottom sweep. Weatherstripping compresses and hardens over time. Once it stops sealing, your AC bill notices before you do.
• The door panel rattles when closed or in wind. Worn rollers and compressed weatherstripping let the panel move in the track. That movement wears the track edge and can oblong the roller holes in the stile.
• The track is visibly worn, dented, or pitted. South Florida rain drives grit into the bottom track. If the anodized surface is compromised, replacement rollers will ride on raw aluminum and fail quickly. The track may need replacement or repair.

If it is not right in the opening, it will not be right in a hurricane. We treat every CWS door repair with that rule in mind.

Replacement Cost & What’s Included

In Palmetto Bay, CWS sliding door part replacement typically lands in these ranges:

• Roller assembly replacement: $180-$340 per panel, including both rollers, cleaning, and track adjustment.
• Mortise lock or handle set replacement: $140-$280 depending on hardware finish and whether the lock body must be rekeyed to match existing keys.
• Weatherstripping and bottom sweep replacement: $90-$200 per panel, including removing old adhesive and prepping the surface so the new seal actually holds.
• Track replacement or resurfacing: $250-$650 depending on track length, material, and whether the frame is impact-rated.

Every quote is line-item, on paper, before work starts. No change orders, no surprise charges. Parts and labor are stated separately so you see exactly what you’re paying for. The workmanship is covered by our Done Right Promise, and if the part carries a manufacturer warranty, we register it in writing and give you the duration.

DIY or Call Us?

A homeowner in Palmetto Bay can safely check a few things: whether screws on the handle are loose, whether the track has visible debris, and whether the panel sits level when closed. Beyond that, this work gets tricky fast. CWS door panels are heavy; a tempered glass panel for a standard patio opening weighs over 100 pounds. Lifting a panel out of its track without a second person and proper suction cups is how fingers get crushed and glass gets cracked. The roller adjustment screws are often seized from salt corrosion, and forcing them strips the stile. If the door is impact-rated, the glazing and frame tolerances are tighter than standard units, and forcing a misaligned panel can void your windstorm rating. We do this work every week, and we’d rather you call (386) 200-9224 and let us put eyes on the door than end up with a panel on the patio concrete. The estimate is free.

FAQs