CWS Custom Windows & Doors Nationwide | TruePane Windows & Doors

CWS Custom Windows & Doors in Palmetto Bay: What to Know First

We service CWS custom windows and doors throughout Palmetto Bay as an independent provider, with most custom glass and glazing work completed in a single visit. Typical CWS repairs run $180 to $340 for securing a failing lite or reglazing a sash, while full frame replacements on custom shapes start around $900 and climb with size and impact rating. If you own a CWS window with a fogged seal, a door that binds, or an arch-top that leaks at the mull, call (386) 200-9224 for a straight read on whether to repair or replace.

Call (386) 200-9224

This page is written for Palmetto Bay homeowners who own CWS windows or doors and want specifics, not a sales pitch. We’ve worked on enough CWS product in this part of Miami-Dade to know exactly where it holds up and where it fails.

How CWS Products Fail - and How We Fix Them

CWS builds a solid commercial-grade frame, but South Florida weather finds every seam eventually. Here’s what we see specifically on custom CWS work in Palmetto Bay:

• Butt-glazed corner joints separating on custom shape windows. The CWS 400 series and similar commercial-style frames rely on precise silicone butt joints at corners, especially on radius tops and trapezoids. After eight to ten years of Palmetto Bay’s wet-dry cycles, that seal lets go and you get a weep that runs down the interior drywall. We disassemble, clean the old silicone fully, prime the joint, and re-glaze with a commercial-grade structural sealant rated for continuous UV exposure.
• Weep system blockage on CWS horizontal sliders. CWS sliders drain through a baffled weep channel in the sill track. Palmetto Bay’s oak pollen and fine sand clog those channels, and the track starts holding water after a hard rain. You’ll see staining at the sill corners, then the rollers sit in water and grind. We clear the weeps, replace the rollers if the bearings are scored, and re-level the panel so it drains the way the factory intended.
• Curtain wall and storefront glazing failing at the wedge gaskets. On CWS commercial curtain wall sections used in larger custom homes, the wedge gaskets that hold glass in place lose their rebound after years of heat. You get glass chatter in wind and eventually a leak at the gasket edge. The right fix is pulling the pressure plate, installing new wedge gasket stock with a durometer match to the original, and re-torquing the plate to spec. Aftermarket gasket that is too soft fails within a season.
• Archtop CWS windows with stress cracks at the apex. On radius and half-round units, we will see a hairline crack running down from the crown. That is almost always the result of the rough opening settling, not a glass defect. The Palmetto Bay soil here, particularly nearer to Old Cutler Road, shifts enough over decades to put the frame in a slight bind. We can replace the lite, but unless the opening is re-shimmed first, the replacement will crack the same way. We do both in one call.
• SDLs and architectural grilles loosening from thermal cycle. CWS simulated divided lites are applied to the interior glass surface, and the adhesive bond between the grille bar and the lite breaks down from repeated expansion and contraction. The bar starts sagging or rattles when you close the door or window. We remove the old bar, clean the glass completely, and re-apply with the correct adhesive and alignment jig so the gridline runs true. This is where our thirty-plus years of glazing shows; a grille set a sixteenth off looks wrong forever.

Our CWS Custom Windows & Doors Process

Here is how a CWS job goes, from the first call to the final check:

1. 1
   Call and talk to a person. You reach a live person at (386) 200-9224, any hour. We ask about the symptom and the window or door type. If it is a CWS custom unit, we note the series and rough dimensions before the tech arrives.
2. 2
   On-site diagnosis. A uniformed tech comes out, measures the opening, checks the frame for true, looks for the leak or the bind, and confirms the failure mode. We can often tell you the problem and the fix before we leave the first visit.
3. 3
   Parts decision. CWS still supports many of its commercial lines, and where OEM makes sense, that is what we use. Where the original part was undersized for our climate or no longer available, we recommend a quality equivalent that meets or exceeds the original spec. We will show you both prices on paper.
4. 4
   The repair or replacement. We do the work with the frame checked for plumb and the rough opening corrected if needed. Glass units are set square and sealed, not just caulked around. That distinction is what separates a patch job from a repair that holds.
5. 5
   Water test and alignment check. Once the work is in, we run a water test on the repaired area and check operation in both directions. The door or window has to open and close the way it did when new, or the job is not finished.
6. 6
   Warranty registration and cleanup. We register both warranty layers in writing before the truck leaves, walk you through what was done, and leave the site clean. The Done Right Promise covers the workmanship.

What CWS Custom Windows & Doors Costs in Palmetto Bay

Here are real numbers for the CWS work we do most often in Palmetto Bay:

• Fogged lite replacement on a CWS custom shape window: $220 to $380, depending on glass type and whether the unit is impact-rated.
• Reglazing a butt joint or pressure plate on a storefront-style CWS unit: $180 to $320 per seam.
• Roller replacement and weep clearing on a CWS slider: $160 to $240 per panel.
• Full custom window replacement with CWS or comparable impact-rated product: $900 to $2,400 per opening, driven by size, shape complexity, and glass spec.
• Custom door, including hardware and threshold reset: $700 to $1,800 depending on door height, glass, and frame condition.

What moves the price: the shape of the unit (radius tops and trapezoids cost more to cut and set), whether the existing frame can be saved, and whether the glass needs to be impact-rated for current Palmetto Bay code. We write the quote before work starts, and it does not change at the end. Call (386) 200-9224 for a free estimate on your specific CWS unit.

Why Palmetto Bay Homeowners Call TruePane Windows & Doors for CWS Work

Dale Kessler has worked windows and doors in this part of Miami-Dade for nearly two decades, and he has seen enough CWS product installed in Palmetto Bay to know its quirks better than most. We are not a franchise crew running through a script. We are a local company that has been serving this community since 2008, and we plan to be here in another thirty. That matters when you are deciding whether to repair a custom window or replace it.

Our techs measure every CWS opening twice and set every lite true, which is the entire reason the company is named TruePane. Every job carries the Done Right Promise, and we register both warranty layers in writing before leaving your driveway. If a CWS custom unit needs to come out and be replaced with something else, we are also an authorized installer for, PGT, and a dozen other lines. You will always see side-by-side quotes on paper, so you know exactly what you are buying.

FAQs