Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Window Replacement: The Palmetto Bay Owner’s Guide
CGI window replacement in Palmetto Bay typically runs $850 to $2,200 per window installed, depending on the CGI series, size, and whether the frame needs rebuilding. We stock CGI-compatible window parts on our trucks, so most swaps in the Palmetto Bay area are done in a single visit. Most homeowners discover the problem the way you probably did: a crank that binds, a latch that will not throw, or a pane that has gone cloudy between the glass where nobody can wipe it. When a CGI window starts failing, it rarely announces itself all at once. It usually begins as a stubborn corner, a drip after a hard rain, or a room that will not hold temperature in August the way it did ten years ago.
Key Takeaways
- We replace CGI window assemblies and components, matched to your series and size, usually same visit.
- Installed costs in Palmetto Bay run $850 to $2,200 per window, with the range driven by frame condition and glass spec.
- CGI windows can often be repaired rather than replaced; we will tell you which makes sense and quote both ways.
- Parts and labor are quoted up front, in writing, with both warranty layers registered before the truck leaves.
Which CGI Models This Applies To
CGI makes several window lines that show up throughout Palmetto Bay, and parts are not interchangeable across all of them. The most common series we work on are the Estate Collection, the Targa Series, and CGI’s fixed and casement impact windows. The Estate line tends to use a heavier frame profile and different balance hardware than the Targa. If you are trying to identify what you have, look for the CGI sticker on the window sash or the head jamb. It will carry a series name and a manufacturing code. That code matters; ordering a part by “CGI window latch” alone is how people end up with hardware that nearly fits but will not seat under wind load.
When it comes to OEM versus aftermarket, our position is simple: for CGI impact windows we recommend OEM parts wherever CGI still produces them. South Florida building code, including what Palmetto Bay enforces, is built around the tested assembly, not the individual part. A generic replacement could get you a window that opens and closes but was never tested to the same pressure rating. We carry the most common OEM CGI components on the truck and can order anything else quickly. We are an independent service provider and not affiliated with CGI, but we have been working on their windows in this part of Miami-Dade for going on two decades.
Signs Your CGI Window Replacement Is Failing
- The crank turns but the sash hesitates or grinds. The operator gears inside the crank assembly wear flat after years of salt air and grit. When the teeth skip, you feel a jerk in the handle before the window moves.
- The latch will not throw or will not hold. On CGI casement and awning windows, the multi-point locks can fall out of alignment as the frame settles or the hinges wear. Once the lock plate is out of plane, no amount of force fixes it; the hardware needs to be replaced or the hinge rebuilt.
- Water gathers on the sill after a heavy rain, even with the window closed. This usually traces to a failed gasket or a weep hole that has clogged with Palmetto Bay’s mix of oak pollen and blown sand. Left alone, the water finds its way into the frame channel and the wood or drywall below.
- You see daylight around the weatherstripping. The rubber glazing and compression seals on CGI windows harden in Florida’s UV exposure. Once the seal takes a set and no longer springs back, air and rain follow the gap.
- Condensation builds between the two panes and will not clear. That is a failed insulated glass seal. The argon, if the unit had it, has escaped. The window still functions mechanically, but it has lost its energy performance and the clouding is permanent.
Replacement Cost & What’s Included
In Palmetto Bay, expect to pay $850 to $1,700 for a straightforward CGI window component replacement and $1,400 to $2,200 when the entire sash or frame assembly is swapped. The biggest cost drivers are the glass specification (impact versus non-impact, low-E coatings, and any decorative divided lites) and whether the existing frame is square and sound. If the frame is rotted or out of plumb, we rebuild it. There is no scenario where we install a new window into a bad opening and call it done. If the pane is not true, the job is not done.
Every quote includes the part, the installation labor, haul-away of the old assembly, and registration of both warranty layers in writing before the truck leaves the driveway. That registration step is one of the things that gets skipped by other installers, and it is exactly the kind of skipped detail that leaves a homeowner holding a voided manufacturer warranty. Our workmanship is covered by the Done Right Promise: if it is not right, we make it right, with no paperwork fights.
DIY or Call Us?
With a CGI impact window, there are a few things you can safely do before calling: check for debris in the track, tighten a visibly loose screw on the crank handle, and confirm the window is not simply locked in a partially open position. Those take ten minutes and cost nothing. Beyond that, this work stops being simple quickly. Impact windows are a tested assembly, and swapping hardware or glass on a window rated for a Category 5 storm is not the place to learn as you go. We have seen homeowners buy a discounted sash online, install it themselves, and then discover during a rain event that it was never going to seal against 60-mile-per-hour wind-driven water because it was from the wrong CGI series entirely.
If it is not right in the opening, it will not be right in a hurricane. If you suspect the window is failing, call us at (386) 200-9224. We will come out, look at it, and give you a straight answer with a written price, whether that is a repair or a replacement.
FAQs
A properly installed and maintained CGI impact window in Palmetto Bay will typically last 20 to 30 years, though the gaskets, weatherstripping, and crank hardware usually need replacement between years 10 and 15. Salt air and UV are hard on seals and moving parts, even when the glass and frame are still sound. Call (386) 200-9224 to have your existing window assessed; we will tell you honestly whether it needs service or replacement.
In many cases, yes; failed operators, locks, gaskets, and even clouded insulated glass units can often be swapped without replacing the entire frame. The only situations that force full replacement are structurally compromised frames, opening sizes that no longer match current CGI components, or damage that has spread into the wall itself. We will quote both options when it is practical and explain the tradeoff plainly before you decide.
Most single-window component replacements in Palmetto Bay take two to four hours on site, from removing the old assembly to cleaning up and registering the warranty. If the frame needs rebuilding or the opening needs correction, expect most of a day. We will give you a straight answer on timing before the work is scheduled, and we will be there when we say.
We stock the most commonly failing CGI components on our trucks, including operators, lock sets, gaskets, and standard insulated glass units matched to the Estate and Targa lines most common in Palmetto Bay. If a part is not on the truck, we order it direct and give you the lead time up front. Call (386) 200-9224 with the sticker information from your window and we will tell you what we can match same day.
Call TruePane for Your CGI Window Replacement in Palmetto Bay
If your CGI window is binding, leaking, or clouded between the panes, the fastest way to a straight answer is a phone call. We have been doing window and door work in this part of Miami-Dade since 2008, and Dale Kessler grew up near Old Cutler Road, so he knows what the coastal air does to a window over twenty summers. You will get a live person when you call, a uniformed and background-checked technician when we arrive, and a written line-item quote before any work starts. Call (386) 200-9224 to schedule your free estimate for a CGI window replacement in Palmetto Bay. We stand behind it.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Palmetto Bay and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.